MIL-STD-100 Engineering Drawings S/S By Asme-Y14.100, Asme-Y14.24, Asme-Y14.35M, And Asme-14.34MThis standard, along with ASME Y14.100M, establishes the essential requirements and reference documents applicable to the preparation and revision of engineering drawings and associated lists for or by Departments and Agencies of the Department of Defense. ASME Y14.100M is the preferred requirements document for engineering drawing practices. This standard should only be used in lieu of ASME Y14.100M where the necessity for a DoD design activity is fully justified and Government logistics support is required

Pages 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 20 - 21 - 22 - 23 - 24 - 25 - 26 - 27 - 28 - 29 - 30 - 31 - 32 - 33 - 34 - 35 - 36 - 37 - 38 - 39 - 40 - 41 - 42 - 43 - 44 - 45 - 46 - 47 - 48 - 49 - 50 - 51 - 52 - 53 - 54 - 55 - 56 - 57 - 58 - 59 - 60 - 61 - 62 - 63 - 64 - 65 - 66 - 67 - 68 - 69 - 70 - 71 - 72 - 73 - 74 - 75 - 76 - 77 - 78 - 79 - 80 - 81 - 82 - 83 - 84

MIL-STD-1OOG

PARAGRAPH CHAPTER 100		PREPARATION OF ENGINEERING DRAWINGS	PAGE 26
100.	General		26
101.	Basic practices		26
101.1	Metric practices		26
101.2	Graphic symbols, designations, letters symbols and abbreviations		26
101.2.1	Graphic symbols		26
101.2.2	Graphic symbols for flueric power diagrams		26
101.2.3	Ship structural symbols		26
101.3	Printed board drawings		26
101.4	Data preparation, maintenance, delivery, or access		26
101.4.1	Materials		26
101.4.1.1	Plastic sheet or roll		26
101.4.1.2	Paper, tracing		26
101.4.1.3	Film, Diazotype		27
101.4.2	Digital data		27
101.4.2.1	Plotters		27
101.4.2.2	Maintenance		27
101.4.2.3	Associated lists, materials		27
101.4.2.4	Physical media		27
101.4.2.5	Initial Graphics Exchange Specification (IGES)		27
101.4.2.6	Raster data files		27
101.4.2.7	Standardized General Markup Language (SGML)		27
101.4.3	Preparation of duplicate original		27
101.5	Drawing marking for item and packaging identification		27
101.5.1	Drawing requirements for part identification marking		27
101.5.2	Packaged items		27
101.5.3	Altered, selected, or source control item identification		27
101.5.4	Printed board assemblies		28
101.6	Code Identification, FSCM and CAGE Code		28

CHAPTER 200 TYPES OF ENGINEERING DRAWINGS 29

200.	General	29
201	Drawing types	29
201.1	Standard microcircuit drawing (SMD)	29
201.1.1	SMD requirement	29
201.1.2	SMD limitation	29

Vll