MIL-STD-100 Engineering Drawings S/S By Asme-Y14.100, Asme-Y14.24, Asme-Y14.35M, And Asme-14.34MThis standard, along with ASME Y14.100M, establishes the essential requirements and reference documents applicable to the preparation and revision of engineering drawings and associated lists for or by Departments and Agencies of the Department of Defense. ASME Y14.100M is the preferred requirements document for engineering drawing practices. This standard should only be used in lieu of ASME Y14.100M where the necessity for a DoD design activity is fully justified and Government logistics support is required

Pages 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 20 - 21 - 22 - 23 - 24 - 25 - 26 - 27 - 28 - 29 - 30 - 31 - 32 - 33 - 34 - 35 - 36 - 37 - 38 - 39 - 40 - 41 - 42 - 43 - 44 - 45 - 46 - 47 - 48 - 49 - 50 - 51 - 52 - 53 - 54 - 55 - 56 - 57 - 58 - 59 - 60 - 61 - 62 - 63 - 64 - 65 - 66 - 67 - 68 - 69 - 70 - 71 - 72 - 73 - 74 - 75 - 76 - 77 - 78 - 79 - 80 - 81 - 82 - 83 - 84

MIL-STD-1OOG

6.  NOTES

(This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.)

6.1  Intended use.  The requirements contained herein apply to hardcopy drawings, digital data file(s), associated lists and textual data resulting from the contractual application of DOD-D-

1000, MIL-DTL-31000 or MIL-T-47500.

6.1.1  Applicability.  The current document specifying engineering drawings as a technical data package element is MIL-DTL-31000.  DOD-D-1000 and MIL-T-47500 are inactive for new design.

6.2  Acquisition requirements.

6.2.1  Issue of DODISS.  When this standard is used in acquisition, the applicable issue of the

DODISS must be cited in the solicitation (see 2.1.1, and 2.2).

6.2.2  Tailoring guidance.  To ensure proper application, MIL-STD-100G and ASME Y14.100M must be tailored to exclude unnecessary requirements.  It is essential that the contractual applicability of the numerous referenced documents, as contained in these two standards, especially regarding basic practices, be as definitive as practicable.  Any tailoring of MIL-STD-100G and ASME Y14.100M must also be consistent with MIL-DTL-31000, TDP Option Selection Worksheets.  Although the manner and extent of such tailoring will vary in accordance with program or end-item requirements, the following is provided as a minimum for consideration in acquisition documents:

TAILORING

A. Drawing Media (Choose all that apply) (1) Non-digital (Specify            )

(2) Digital Data (Specify              ) (3) Other (Specify                  )

B. Drawing Format (Choose One) (1)  Contractor

(2)  Government (forms supplied by the Government) (3)   Government (forms supplied by the Contractor)

C. Drawing Sheet Size (and Format) (Choose One) (1)  ASME Y14.1

(2)  ASME Y14.1M

19